Silicone Molding Methods Compared: LSR, HCR, and Compression Molding

Date Published


When engineers and product teams set out to manufacture silicone parts, one of the most consequential decisions they face is which molding method to use. The choice between Liquid Silicone Rubber (LSR) molding, High Consistency Rubber (HCR) molding, and compression molding shapes everything that follows — from part precision and cycle time to tooling investment and production scalability. Make the right call and you streamline your path from prototype to production. Make the wrong one and you risk over-engineering a simple component or under-specifying a critical one.

Each of these three silicone molding methods works with the same family of base material, but they diverge sharply in how that material is processed, what geometries and tolerances they can achieve, and at what production volumes they make economic sense. This guide breaks down all three methods in clear engineering terms, compares them head-to-head across the factors that matter most, and provides a practical framework for selecting the right process for your specific project.

Written by the NICE Rapid Tooling process engineering team (silicone & LSR molding). Unless a standard is named, the figures in this guide are indicative ranges from our project experience, not published industry data — see the notes and Sources at the end of the article.

Manufacturing Guide

Silicone Molding Methods Compared

LSR injection, HCR transfer, and compression molding — side by side across the factors that matter most for your project.

💧 LSR Injection
🧱 HCR Transfer
🔩 Compression
3
Molding Methods
10s
Fastest Cycle (LSR)
$1.5K
Entry Tooling Cost
±0.05
Best Tolerance (mm)
The Three Methods

At a Glance

💧

LSR Injection

Two-part liquid silicone injected into a heated closed mold. Platinum-cured, fully automated, ultra-precise.

⚡ 10 – 60 sec cycle
🎯 ±0.05 – ±0.10 mm tolerance
💰 $8K – $30K+ tooling
📦 5,000 – 1,000,000+ parts
Best for: High-volume, complex, precision parts
🧱

HCR Transfer

Solid gum-like silicone milled into preforms, loaded into a pot and pressed through a gate into the heated cavity.

⏱️ 2 – 5 min cycle
🎯 ±0.20 mm tolerance
💰 $3K – $25K tooling
📦 Low to mid volume
Best for: Implantables, specialty compounds, tubing
🔩

Compression

Pre-measured silicone charge placed into an open heated mold; press closes under hydraulic pressure to fill and cure.

⏱️ 1 – 5 min cycle
🎯 ±0.20 – ±0.50 mm tolerance
💰 $1.5K – $6K tooling
📦 50 – 5,000 parts
Best for: Prototypes, large/thick parts, cost-sensitive
Head-to-Head

Decision Matrix

Factor 💧 LSR 🧱 HCR 🔩 Compression
Cycle Time 10 – 60 sec 2 – 5 min 1 – 5 min
Tooling Cost $8K – $30K+ $3K – $25K $1.5K – $6K
Tolerance ±0.05 – ±0.10 mm ±0.20 mm ±0.20 – ±0.50 mm
Automation HIGH MEDIUM LOW
Part Complexity High ✓ Medium Low – Medium
Flash Low Moderate High
Biocompatibility Grade-dependent (21 CFR 177.2600 / ISO 10993-1) Implant-grade compounds available Grade-dependent
Optimal Volume 5K – 1M+ parts Low – Mid 50 – 5K parts
Selection Framework

Which Method Is Right for You?

💧

Choose LSR When…

  • → Volume is high enough to amortize LSR tooling
  • → Tight tolerances (±0.05–0.10 mm) are required
  • → Complex geometry: thin walls, undercuts, micro-features
  • → FDA/ISO biocompatibility or cleanroom is mandated
  • → Overmolding onto thermoplastic or metal substrate
🧱

Choose HCR When…

  • → Maximum tensile/tear strength is the priority
  • → Long-term implantable devices (pacemaker leads, catheters)
  • → Specialty compounds not available in liquid form
  • → Low-to-mid volume with moderate geometric complexity
  • → Better consistency than open compression, lower cost than LSR
🔩

Choose Compression When…

  • → Volume is low relative to the tooling investment
  • → Parts are large, thick-walled, or geometrically simple
  • → Design is still evolving — low-cost tooling for iteration
  • → Cycle time is not a program-critical constraint
  • → Budget demands the lowest possible tooling entry point
Volume Rule of Thumb

Volume Rule of Thumb: Where Tooling Cost Crosses Over

50
parts
Compression
is ideal
500
parts
Compression
or HCR
Example
5,000
parts
Crossover varies
by program
50K
parts
LSR
preferred
1M+
parts
LSR most
common
Real-World Use Cases

Industry Applications

🏥

Medical

LSR: Respiratory valves, wearable sensors
HCR: Pacemaker leads, balloon catheters
Comp: Prototype tooling, custom components
🚗

Automotive

LSR: O-rings, connectors, spark plug boots
HCR: Gaskets, vibration-dampening mounts
Comp: Weatherstripping, sealing profiles
📱

Consumer Electronics

LSR: Watch bands, earpiece tips, button covers
HCR: Specialty compound components
Comp: Accessories, custom consumer goods
⚙️

Industrial & Sealing

LSR: Precision seals, fluid control parts
HCR: Diaphragms, pump components
Comp: Large gaskets, custom seals
Summary

5 Key Takeaways

1

All three methods use silicone — the differences are entirely in how the material is processed, cured, and scaled.

2

At low volumes, compression molding usually has the lower total program cost — in the illustrative model below, its lower tooling investment outweighs LSR's faster cycle until roughly 10,900 parts.

3

LSR generally achieves the tightest tolerances and shortest cycles of the three methods in the programs we run (±0.05–0.10 mm, 10–60 s under the conditions noted above), which is why it is commonly selected for high-volume, complex parts.

4

HCR is widely used for long-term implantable components — such as pacemaker lead covers and shunts, because many qualified implant-grade compounds are supplied in millable form. Implant-grade LSR also exists; the decision follows the qualified compound and the device's regulatory file, not the process category.

5

No single method is universally superior — the right choice emerges from the intersection of geometry, volume, tolerance, material spec, and budget.

Need Help Choosing the Right Method?

NICE Rapid supports silicone and LSR molding plus compression molding from prototype to production; for HCR transfer molding and implant-grade compounds, contact our engineering team to confirm scope for your project.

Discuss Your Project →
✓ In-House Tooling & Molding | ✓ Engineering-Led Process Selection | ✓ Prototype to Production
nicerapidtooling.com  ·  Silicone Molding Methods Compared

What Is Silicone Molding?

Silicone molding is a manufacturing process in which silicone rubber is shaped into a finished part by introducing the material into a mold cavity and curing it under controlled heat and pressure. Silicone is selected for its thermal stability, chemical inertness, flexibility and long service life — properties that make it widely used in medical devices, automotive systems, consumer electronics, and industrial sealing applications. Silicone grades typically operate from about -55 °C to 200–230 °C continuously, with short-term excursions up to ~300 °C on heat-stabilized grades; exact limits depend on the compound and exposure time — check the supplier datasheet. The core distinction between silicone molding methods lies in the state of the raw material entering the mold and the mechanism used to cure it. For material-level trade-offs against thermoplastic elastomers, see TPE vs silicone: cost, temperature and compliance compared.

The three dominant methods — LSR injection molding, HCR molding, and compression molding — each represent a different balance between process complexity, tooling investment, part precision, and production throughput. Understanding those trade-offs is the foundation of an informed manufacturing decision. NICE Rapid's silicone molding capabilities cover silicone and LSR molding plus compression molding, allowing product teams to match the right method to each project's requirements; for HCR transfer molding and implant-grade compounds, contact our engineering team to confirm scope.

LSR (Liquid Silicone Rubber) Molding

Liquid Silicone Rubber molding is an injection-based process built around a two-part platinum-cured silicone system. The two liquid components — a base polymer and a catalyst — are metered in a precise 1:1 ratio, blended through a static mixer, and injected under pressure into a heated closed mold, where the material rapidly crosslinks and cures. Because LSR is a thermoset, heat triggers the cure rather than reversing it, which means the mold is kept hot and the delivery system is kept cold to prevent premature curing before injection. This cold-runner architecture is one of the hallmarks of a properly configured LSR system.

The viscosity of LSR before curing is comparably low — often likened to a thick syrup — which enables it to fill intricate mold geometries, thin walls, and fine details that would be impossible or unreliable with solid silicone feedstocks. Once cured, the material offers excellent elastic recovery, broad temperature resistance, and grade-dependent compliance potential: certain LSR grades are formulated to comply with FDA 21 CFR 177.2600 for food contact and can support ISO 10993-1 biological evaluation of the finished device. Compliance depends on the specific grade, processing and post-cure, and must be verified on the final part — the molding process itself carries no certification. LSR also supports overmolding onto thermoplastic or metal substrates, making it a versatile option for multi-material assemblies.

Key Advantages of LSR Molding

  • High precision and dimensional consistency — tolerances typically in the ±0.05 to ±0.10 mm range for well-designed tooling
  • Fast cycle times — typically 10 to 60 seconds per cycle, supporting high-volume output
  • Fully automated process — closed-system metering and injection minimizes contamination risk and labor dependency
  • Grade-dependent biocompatibility — suitable for medical devices, for implant-grade LSR grades where a qualified compound is specified, and for infant and food-contact components; compliance is verified on the finished part
  • Complex geometry capability — thin walls, undercuts, and micro-features are achievable
  • Low flash generation — with good tooling design, post-processing trim requirements are minimal

Limitations of LSR Molding

  • High tooling cost — indicative tooling investment from NICE Rapid projects: roughly $8,000 for a simple single-cavity tool up to $30,000+ for complex, multi-cavity tools (steel grade, part size and cavitation dependent); not a quotation — request a project-specific quote
  • Specialized equipment required — cold-runner systems, metering pumps, and heated mold infrastructure represent significant capital investment
  • Volume needed to recover tooling — the economics improve as volume rises and cycle-time savings offset tooling cost; the crossover depends on cavitation, part weight and labor rate
  • Flash trimming still possible — LSR's low viscosity can cause flash if mold venting and parting line precision are not tightly controlled

For teams scaling toward high-volume production, NICE Rapid's Liquid Silicone Rubber (LSR) Molding service delivers the automation, precision, and throughput that demanding programs require.

Further reading: LSR molding explained: why liquid silicone rubber behaves differently and silicone injection molding: the process controls that drive quality.

HCR (High Consistency Rubber) Molding

High Consistency Rubber — also called millable silicone rubber or heat-cured rubber (HCR) — is a solid, gum-like silicone compound with a much higher viscosity than LSR. Unlike the liquid system, HCR arrives at the press in a pre-mixed solid form that must be milled, weighed, and preformed before being loaded into the mold. Curing is achieved through heat and pressure using either peroxide-based or platinum-based catalyst systems. Peroxide-cured HCR is common for general industrial use, while platinum-cured HCR is preferred when cleanliness, clarity, and low extractables are required — as in medical and food-contact applications.

HCR can be processed through compression molding, transfer molding, or specialized gumstock injection molding. In compression molding applications, the preformed silicone is placed directly into an open mold cavity before the press closes. In transfer molding, a pot of HCR is loaded above the mold and pushed into the cavity through a gate under piston pressure, giving slightly better consistency and geometry control than open-cavity compression. See our detailed guide to transfer molding and where it sits between compression and injection molding. High-tear HCR formulations are often selected for components that must withstand repeated mechanical stress, but tensile strength depends on the specific compound and filler system rather than the process family — compare supplier datasheets for the grades under consideration.

Key Advantages of HCR Molding

  • Compound-dependent tensile and tear strength — tensile strength depends on the compound rather than the process family: general-purpose HCR and LSR grades both fall roughly in the 5–11 MPa range when tested to ASTM D412. High-tear HCR formulations are often selected for mechanically loaded parts — compare supplier datasheets for the specific grades
  • Wide formulation range — available in a broad selection of durometers, pigments, and specialty compounds not always available in LSR form
  • Lower tooling entry cost — mold complexity and equipment requirements are generally lower than LSR injection systems
  • Suitable for large, thick-walled parts — HCR handles thicker cross-sections and larger part sizes efficiently
  • Implant-grade options available — HCR is used in long-term implantable devices such as pacemaker lead covers and catheters, where specific compound performance is required

Limitations of HCR Molding

  • Labor-intensive preparation — milling, weighing, and loading preforms adds time and introduces operator variability
  • Longer cycle times — cure times are generally longer than LSR, limiting throughput for high-volume programs
  • More flash and secondary operations — open-mold or pot-loaded systems tend to generate more flash that must be trimmed post-cure
  • Lower precision versus LSR — typical tolerances run around ±0.20 mm, which may not meet requirements for fine-feature components
  • Less automation-ready — the process relies more heavily on operator skill, making repeatability harder to maintain at scale

Compression Molding for Silicone

Silicone compression molding is a long-established silicone processing method. The process is straightforward: a pre-measured charge of uncured silicone (typically HCR compound) is placed into an open heated mold cavity, the press closes under hydraulic pressure, and the material flows to fill the cavity while curing under controlled heat and dwell time. Once the cycle is complete, the press opens and the part is removed — often with flash at the parting line that requires trimming. The simplicity of this approach is exactly its strength.

Because compression molds require no runners, gates, or cold-runner delivery systems, tooling is significantly less complex and less expensive to build. Indicative tooling investment from NICE Rapid projects is roughly $1,500 to $6,000 for compression molds, compared to $8,000 to $30,000+ for LSR injection tooling (cavitation, steel grade and part size dependent; not a quotation). Because compression tools have no runner or cold-runner system, tool build is usually simpler and faster than LSR tooling. Lead time depends on part size, cavity count and steel selection — we confirm a schedule with the DFM review. This makes compression molding the natural entry point for new programs, low-to-medium volume production, and projects where design iteration is still ongoing. The trade-off is longer cycle times — typically 1 to 5 minutes per cycle — and a heavier reliance on manual loading and finishing operations.

Key Advantages of Compression Molding

  • Low tooling cost — the most accessible entry point for silicone part production
  • Handles large and thick parts — well suited for bulky components where injection flow paths would be impractical
  • Wide material flexibility — compatible with a broad range of silicone grades, colors, durometers, and specialty fillers
  • Less shear stress on material — beneficial for shear-sensitive formulations or compounds that need to retain specific filler properties
  • Lower orientation stress — compression-molded parts show lower flow-induced orientation stress than injection-filled parts, although cure shrinkage and demolding can still introduce residual stress; post-cure and dimensional checks are recommended for tight-tolerance parts

Limitations of Compression Molding

  • Slower cycle times — 1 to 5 minutes per cycle (versus 10 to 60 seconds for LSR), limiting scalability for large programs
  • Parting line flash — flash at the mold parting line requires manual trimming, adding labor and time to every production run
  • Limited complexity — parts with intricate geometries, undercuts, or very thin walls are difficult to produce reliably
  • Dimensional variability — preform charge weight and placement affect fill consistency, introducing more part-to-part variation than injection-based methods
  • Higher labor intensity — manual loading, unloading, and trimming increase per-part labor cost at scale

NICE Rapid's compression molding service is structured to support both prototype tooling and low-to-medium volume production runs, giving product teams a cost-effective path into silicone manufacturing without committing to high-investment injection tooling prematurely. For a deeper look at the process, tooling and best-fit parts, see compression molding explained.

Head-to-Head Comparison: LSR vs. HCR vs. Compression

The table below consolidates the most decision-relevant factors across all three methods. Use it as a fast reference to align process selection with your project's specific requirements.

FactorLSR Injection MoldingHCR Molding (Transfer)Compression Molding
Material FormTwo-part liquid (metered & mixed)Solid gum-like compound (preformed)Solid pre-charge (placed manually)
Cycle Time10 – 60 seconds2 – 5 minutes1 – 5 minutes
Typical Tooling Cost$8,000 – $30,000+$3,000 – $25,000$1,500 – $6,000
Dimensional Tolerance±0.05 – ±0.10 mm±0.20 mm±0.20 – ±0.50 mm
Automation LevelHighLow to MediumLow
Part ComplexityHigh (thin walls, fine features)MediumLow to Medium
Flash GenerationLow (with precision tooling)ModerateHigh (trimming required)
OvermoldingCommon, well-supportedPossible, less commonPossible, less common
Optimal Volume5,000 – 1,000,000+ partsLow to mid volume50 – 5,000 parts
BiocompatibilityGrade-dependent; testing on finished deviceExcellent (implant-grade available)Good (grade-dependent)
Best ForHigh-volume, complex, precision partsSpecialty compounds, implantables, tubingPrototypes, large/thick parts, cost-sensitive programs

Note on the figures above: cycle times, tooling costs, tolerances and volume ranges are indicative ranges from NICE Rapid Tooling project experience, not published industry data and not a quotation. Tooling cost varies with cavitation, steel grade and part size; cycle time with part thickness, compound and cure profile. Tolerances are indicative for well-designed tooling and should be confirmed against the applicable ISO 3302-1 tolerance class and measured on the finished part (typical practice: 3–5 mm thick sections, 23 °C, 24 h after post-cure). Request a project-specific quote and DFM review.

Choosing the Right Silicone Molding Method

The right molding method is never determined by a single factor — it emerges from the interaction of part geometry, production volume, tolerance requirements, material specification, and budget. The following framework is designed to guide that decision in a practical, engineering-first way.

  1. Volume: estimate the lifetime part count and compare total program cost (tooling + cycle time × machine-and-labor rate), not tooling price alone.
  2. Tolerance: if the drawing calls for ±0.05–0.10 mm on fine features, LSR is usually the starting point; confirm the tolerance class against ISO 3302-1 and measure the finished part.
  3. Compound qualification: check whether the required grade exists in liquid (LSR) or millable (HCR) form, and what the device's regulatory file specifies.
  4. Geometry: thin walls, undercuts and micro-features favor LSR; large, thick, geometrically simple parts favor compression.
  5. Budget and schedule: decide how much tooling investment the program can carry now, and whether compression or bridge tooling should precede a production tool.

Choose Compression Molding When:

  • Your production volume is low enough that compression tooling is easier to recover than an LSR injection tool — use the illustrative cost model below rather than treating any single part count as a fixed threshold
  • The part is large, thick-walled, or geometrically simple — gaskets, seals, pads, and industrial grommets are classic compression candidates
  • You are still iterating on design and need low-cost tooling that can be modified without major expense
  • Your material specification requires a specialty HCR compound not readily available in liquid form
  • Cycle time is not a critical constraint for your program schedule

Choose HCR (Transfer) Molding When:

  • Your application demands mechanical properties — particularly tear resistance — for which a specific high-tear HCR grade is qualified
  • You are manufacturing implantable medical devices such as pacemaker lead coverings, shunts, or long-term catheter components where specific HCR compounds are required
  • Part volume is low-to-mid range and the geometry has moderate complexity but does not justify the capital investment of LSR injection infrastructure
  • You need the consistency improvement of a closed transfer system over open compression, but do not require the full precision of LSR injection

Choose LSR Injection Molding When:

  • Production volumes are high enough to amortize tooling investment against the cycle-time savings of a 10–60 second injection cycle (the crossover depends on cavitation, part weight and labor rate — see the model below)
  • Part geometry is complex — thin walls, fine details, undercuts, or micro-features that solid feedstocks cannot reliably fill
  • Tight dimensional tolerances (±0.05 to ±0.10 mm) are a hard requirement, as in precision medical components or automotive sealing systems
  • Biocompatibility, cleanroom compatibility, or regulatory compliance demands a closed, fully automated system that minimizes contamination risk
  • Overmolding onto a thermoplastic or metal substrate is part of the design

There is no universal part-count threshold. Total program cost crosses over where the tooling premium of the faster process is repaid by its lower per-part conversion cost. In the illustrative model below (assumptions: one cavity; $2,500 compression tool, $6,000 HCR transfer tool, $12,000 LSR tool; 3-min compression cycle, 3.5-min HCR transfer cycle including preform preparation, 30-s LSR cycle; a combined press-and-labor rate of $0.35/min; material cost per part assumed equal across methods and excluded; no trimming allowance), total program cost crosses over at roughly 10,900 parts between compression and LSR. This is an example model, not a quotation — your crossover depends on cavitation, part weight, cure profile and labor rate, and we can model it against your CAD.

Program volumeCompression (tool + conversion)HCR transfer (tool + conversion)LSR injection (tool + conversion)
1,000 parts$3,550$7,225$12,175
5,000 parts$7,750$12,125$12,875
50,000 parts$55,000$67,250$20,750

Illustrative model only, based on the assumptions listed above. To see how tooling investment can be staged before committing to a production tool, read injection molding tools compared: soft, bridge and production tooling.

Industry Applications by Method

Understanding where each method is most commonly deployed across key industries helps anchor the technical comparison in real-world context.

Medical and Healthcare

LSR is commonly selected where precision, grade-qualified biocompatibility and automation are priorities — think respiratory valves, infusion device components, wearable sensor housings, and baby care products, where the finished part is verified against the applicable requirements (FDA 21 CFR 177.2600 for food contact, ISO 10993-1 biological evaluation for device contact). HCR is widely used for long-term implantable components, pacemaker lead coverings, balloon catheters, and extruded silicone tubing where a qualified implant-grade compound is specified in the device's regulatory file. Compression molding serves lower-volume custom medical components and prototype tooling during early device development.

Automotive

Automotive applications span all three methods depending on the component. LSR injection molding is used for precision o-rings, electrical connectors, spark plug boots, and sensors requiring tight tolerances and thermal stability across extreme temperature cycles. HCR handles gaskets, grommets, and vibration-dampening mounts where tensile toughness is the primary selection criterion. Compression molding is common for larger sealing profiles, weatherstripping prototypes, and custom elastomeric pads where geometry is simple and volumes do not justify injection tooling.

Consumer Electronics and Wearables

LSR injection molding is the process of choice for smartwatch bands, button covers, earpiece tips, and phone cases that need high cosmetic consistency, soft skin-contact properties, and complex surface textures replicated across hundreds of thousands of units. Compression molding supports smaller runs of silicone accessories, promotional items, and custom consumer goods where tooling simplicity keeps program cost manageable.

Industrial and Sealing

Industrial sealing and fluid control applications are a natural fit for all three methods. Compression molding handles large gaskets, custom seals, and pad components cost-effectively at lower volumes. HCR transfer molding delivers durable diaphragms and pump components with demanding mechanical property requirements. LSR injection molding serves high-volume precision sealing systems, electrical insulation components, and fluid control parts in automated production environments.

Across all of these industries, NICE Rapid supports customers at every stage — from rapid prototyping using vacuum casting, 3D printing, and CNC machining, through to low volume, mid volume, and high volume manufacturing — with silicone molding integrated across that full lifecycle.

Frequently Asked Questions

Is LSR cheaper than compression molding?

Not at low volumes — LSR usually costs more per program until the part count is high enough for its shorter cycle to offset the higher tooling investment. In the illustrative model above (single cavity, $12,000 LSR tool vs $2,500 compression tool, 30-s vs 3-min cycle, $0.35/min press-and-labor rate), the crossover falls at roughly 10,900 parts; your figure depends on cavitation, part weight and labor rate.

Which silicone molding method suits medical parts?

The method follows the qualified compound and the device's regulatory file, not the other way round. LSR is commonly used for high-volume precision components, while HCR is widely used for long-term implantable components where qualified implant-grade compounds are supplied in millable form. Compliance is grade- and part-specific: certain grades are formulated to comply with FDA 21 CFR 177.2600 for food contact and can support ISO 10993-1 biological evaluation of the finished device — no molding process carries a certification itself.

Can HCR be injection molded?

Yes — HCR can be processed by specialized gumstock injection molding as well as by compression and transfer molding. It is not the same as LSR injection: the solid compound must be milled, weighed and preformed before it is fed, so preparation labor and cycle times remain higher than for a metered liquid system.

Partner With NICE Rapid for Silicone Molding

LSR, HCR, and compression molding are not competing technologies in the sense that one is inherently superior. They are complementary tools, each optimized for a specific intersection of part requirements, material properties, production volume, and budget constraints. The engineer's task is not to identify a universally superior method — it is to identify the right method for the specific program at hand. That distinction drives the difference between a project that flows smoothly from prototype to production and one that accumulates avoidable cost and delay.

NICE Rapid supports silicone and LSR molding plus compression molding, with engineering-led process selection guidance and a scalable production infrastructure that grows with your program; for HCR transfer molding and implant-grade compounds, contact our engineering team to confirm scope. Whether you are validating a new medical device component with a compression molding prototype tool or scaling a consumer electronics program with multi-cavity LSR injection tooling, NICE Rapid is equipped to support you at every stage. Explore our full services overview to see how our capabilities span the complete product manufacturing lifecycle.

Ready to Choose the Right Silicone Molding Method?

Whether you need compression molding for a prototype run, HCR transfer molding for a regulated device, or high-volume LSR injection molding for a production program, NICE Rapid's engineering team is ready to help you make the right call — and execute it. Get in touch to discuss your project requirements.

Contact Us

Sources and Standards Referenced

Cycle times, tooling costs, tolerances and volume ranges in this article are indicative ranges from NICE Rapid Tooling project experience and are not quotations. Property and compliance statements should be verified against the following standards and against the technical datasheet of the specific compound:

  • ISO 10993-1 — Biological evaluation of medical devices; evaluation and testing within a risk management process. Applies to the finished device, by contact type and duration.
  • FDA 21 CFR 177.2600 — Rubber articles intended for repeated use. Food-contact compliance is a property of the specific formulation and its processing, not of a molding process.
  • ISO 3302-1 — Rubber: tolerances of products (dimensional tolerance classes for molded parts).
  • ASTM D412 — Standard test methods for tensile properties of vulcanized rubber and thermoplastic elastomers.
  • ASTM D2240 — Standard test method for rubber property: durometer hardness.
  • Compound-specific values (tensile strength, tear resistance, hardness, continuous and peak temperature limits, cure and post-cure profile): the silicone supplier's technical datasheet for the grade specified. These values vary by compound and are not constants of a process family.